Resetting a Maytag washer can resolve many common errors, such as unresponsive controls, error codes, or cycles that fail to start or complete. Follow the steps below to reset your washer and address potential issues.
What Are the Signs You Need to Reset a Maytag Washer?
A Maytag washer typically requires a reset when it displays the following:
- Error codes (e.g., “F21,” “LF”).
- Unresponsive control panel or buttons.
- Washer stuck in a cycle or fails to start.
- Door remains locked after a cycle.
How to Reset a Maytag Washer: Step-by-Step Guide
1. Perform a Basic Reset
To execute a soft reset, follow these steps:
- Power Off: Turn the washer off using the “Power” button.
- Unplug the Washer: Disconnect it from the power source.
- Wait for 1–2 Minutes: Allow the electrical charge to dissipate.
- Plug Back In and Power On: Reconnect and press the “Power” button.
This process clears minor glitches in the control board.
2. Reset a Top-Load Maytag Washer
For models with top-load functionality, use the following:
- Turn the Dial to ‘Normal’: Ensure the cycle selector is set to “Normal.”
- Perform a Button Combination Reset: Do the following sequence:
- Turn the dial one click counterclockwise, three clicks clockwise, one click counterclockwise, and one click clockwise.
- Start the Calibration Mode: Wait for all lights to blink. Then press “Start” to begin the recalibration.
3. Reset a Front-Load Maytag Washer
For front-load washers, use this approach:
- Press and Hold Start/Pause Button: Hold for 3–5 seconds.
- Check Error Codes: If any errors remain, refer to the washer’s manual to clear them.
- Perform a Hard Reset if Necessary: Unplug the washer for 10 minutes.
Hard Reset Instructions for Persistent Issues
If your Maytag washer is still malfunctioning after a basic reset, perform a hard reset:
- Unplug the Washer: Remove power completely.
- Wait 10 Minutes: This allows the control board to reset fully.
- Reconnect Power: Plug the washer back into the outlet.
- Start a Test Cycle: Select a light wash cycle to ensure proper functioning.
Error Codes That May Require a Reset
Certain Maytag washer error codes can indicate the need for a reset:
| Error Code | Meaning | Solution |
|---|---|---|
| F21 | Long Drain Time | Check drain hose/blockages. |
| F01 | Electrical Fault | Reset control board. |
| LF (Long Fill) | Water Supply Issue | Inspect hoses or water valve. |
| dL or dU | Door Lock/Unlock Issue | Ensure door closes properly. |
Preventing Future Issues
Follow these maintenance tips to avoid frequent resets:
- Clean the Drain Filter: Monthly cleaning prevents clogs.
- Check Hoses: Inspect for kinks or leaks regularly.
- Avoid Overloading: Distribute clothes evenly during loading.
- Use Correct Detergent: HE detergent is recommended for Maytag washers.
FAQ How to Reset a Maytag Washer
How Do I Hard Reset My Maytag Washer?
To hard reset your Maytag washer:
- Unplug the Washer: Disconnect it from the power source.
- Wait 10–15 Minutes: This ensures the control board fully resets.
- Reconnect Power: Plug the washer back in.
- Select a Test Cycle: Run a light wash cycle to confirm the reset worked.
How Do You Hard Reset a Washing Machine?
For most washing machines, including Maytag models:
- Power Off: Turn off the machine using the control panel.
- Disconnect from Power: Unplug the washer from the outlet.
- Wait for 5–10 Minutes: Let the internal memory clear.
- Reconnect and Restart: Plug it back in and power it on to resume normal operation.
How Do I Reset My Maytag Control Panel?
To reset the control panel on a Maytag washer:
- Press and Hold the Start/Pause Button: Hold it for 3–5 seconds.
- Unplug the Washer: Remove it from the power source for 1–2 minutes.
- Reconnect Power: Plug it back in.
- Test the Panel: Press a cycle button to ensure the panel responds properly.
How Do You Reset a Maytag Washer Stuck on Sensing?
If your Maytag washer is stuck on the sensing phase:
- Press and Hold the Start/Pause Button: Hold for 3–5 seconds to reset the cycle.
- Turn the Dial to ‘Normal’: Use the cycle selector to set it to “Normal.”
- Perform a Combination Reset:
- Rotate the dial one click counterclockwise, three clicks clockwise, one click counterclockwise, and one click clockwise.
- Restart the Washer: Press the Start button to initiate a new cycle.
Conclusion
How to reset Maytag washer can be a simple and effective solution for common issues such as control system malfunctions or power supply issues. However, it is important to note that resetting the machine will not fix all problems, and it’s important to consult the user manual or diagnostic codes for troubleshooting tips. Also, Read about why Maytag Washer Won’t Start? guide post
